Canning

Canning

Canning is a method of preserving food in which the food is processed and sealed in an airtight container. The process was first developed as a French military discovery. The packaging prevents microorganisms from entering and proliferating inside.

To prevent the food from being spoiled before and during containment, quite a number of methods are used: pasteurization, boiling, other means of high temperature applied over a period of time, refrigeration, outright freezing, drying, vacuum treatment, antimicrobial agents that are natural to the indigenous recipe of the foodstuff being preserved, or otherwise are applied to the contents of the can, a sufficient dose of ionizing radiation, submersion in a strongly saline, acid, base, osmotically extreme (e.g. very sugary) or otherwise microbially challenging environments.

No such countermeasure is perfectly dependable as a preservative. E.g. spore-forming thermo-resistant microorganisms, such as "Clostridium botulinum" (the causative agent of botulism) can still survive.

From a public safety point of view, foods with low acidity, i.e. pH more than 4.6 need sterilization under high temperature (116-130°C). Foods that must be pressure canned include most vegetables, meats, seafood, poultry, and dairy products. The only foods that may be safely canned in an ordinary boiling water bath are highly acidic ones with a pH below 4.6 [http://www.extension.umn.edu/distribution/nutrition/DJ1097.html] , such as fruits, pickled vegetables, or other foods to which acidic additives have been added.

History

::"An army marches on its stomach." —Napoleon

During the first years of the French Revolutionary Wars, the notable French newspaper "Le Monde", prompted by the government, offered a hefty cash award of 12,000 francs to any inventor who could come up with a cheap and effective method of preserving large amounts of food. The new, larger armies of the period required increased, regular supplies of quality food; limitations on food availability were among the factors restricting effective military campaigns to the summer and fall months. In 1809, the French confectioner Nicolas François Appert observed that food cooked inside a jar did not spoil unless the seals leaked, thus developed a method of sealing food inside glass jars. The reason why food did not spoil was unknown at the time, since it would be another 50 years before Louis Pasteur demonstrated the role of microbes in food spoilage. However, glass containers presented challenges for transportation.

Glass jars were largely replaced in commercial canneries with cylindrical tin or wrought-iron canisters (later shortened to "cans") following the work of Peter Durand (1810). Cans are both cheaper and quicker to make and much less fragile than glass jars. Glass jars have, however, remained popular for some high-value products and in home canning. Tin-openers were not to be invented for another thirty years — at first, soldiers had to cut the cans open with bayonets or smash them open with rocks. The French Army began experimenting with issuing tinned foods to its soldiers, but the slow process of tinning foods and the even slower development and transport stages prevented the army from shipping large amounts around the French Empire, and the war ended before the process could be perfected. Unfortunately for Appert, the factory which he had built with his prize money was burned down in 1814 by Allied soldiers invading France. in his voyage to find a northwestern passage to India. Throughout the mid-nineteenth century, tinned food became a status symbol amongst middle-class households in Europe, becoming something of a frivolous novelty. Early methods of manufacture employed poisonous lead solder for sealing the tins, which had disastrous consequences for the 1845 Franklin expedition to the Arctic Ocean.

Increasing mechanisation of the canning process, coupled with a huge increase in urban populations across Europe, resulted in a rising demand for tinned food. A number of inventions and improvements followed, and by the 1860s, the time to cook food in sealed cans had been reduced from around six hours to only thirty minutes. Canned food also began to spread beyond Europe — Robert Ayars established the first American canning factory in New York City in 1812, using improved tin-plated wrought-iron cans for preserving oysters, meats, fruits and vegetables. Demand for tinned food greatly increased during wars. Large-scale wars in the nineteenth century, such as the Crimean War, American Civil War, and Franco-Prussian War introduced increasing numbers of working-class men to tinned food, and allowed canning companies to expand their businesses to meet military demands for non-perishable food, allowing companies to manufacture in bulk and sell to wider civilian markets after wars ended. Urban populations in Victorian era Britain demanded ever-increasing quantities of cheap, varied, good-quality food that they could keep on the shelves at home without having to go to the shops every day for fresh produce. In response, companies such as Nestlé, Heinz, and others emerged to provide shops with good-quality tinned food for sale to ordinary working class city-dwellers. The late 19th century saw the range of tinned food available to urban populations greatly increase, as rival canning companies competed with each other using novel foodstuffs, highly decorated printed labels, and lower prices.

Demand for tinned food skyrocketed during World War I, as military commanders sought vast quantities of cheap, high-calorie food to feed their millions of soldiers, which could be transported safely, survive trench conditions, and not spoil in between the factory and the front lines. Throughout the war, soldiers generally subsisted on very low-quality tinned foodstuffs, such as the British "Bully Beef" (cheap corned beef), pork and beans and Maconochies Irish Stew, but by 1916 widespread boredom with cheap tinned food amongst soldiers resulted in militaries purchasing better-quality food, in order to improve low morale, and the first complete meals in a tin began to appear. In 1917 the French Army began issuing tinned French cuisine, such as coq au vin, whilst the Italian Army experimented with tinned ravioli and spaghetti bolognese. Shortages of tinned food in the British Army in 1917 led to the government issuing cigarettes and even amphetamines to soldiers to suppress their appetites. After the war, companies that had supplied tinned food to national militaries improved the quality of their goods for sale on the civilian market.

Today, tin-coated steel is the material most commonly used. Laminate vacuum pouches are also now used for canning, such as those found in an MRE.

Double seams

Modern double seams provide an airtight seal to the tin can. This airtight nature is crucial to keeping bacteria out of the can and keeping its contents sealed inside. Thus, double seamed cans are also known as Sanitary Cans. Developed in 1900 in Europe, this sort of can was made of the traditional cylindrical body made with tin plate; however, the two ends (lids) were attached using what is now called a double seam. A can thus sealed is impervious to the outside world by creating two tight continuous folds between the can’s cylindrical body and the lid at each end. This eliminated the need for solder and allowed improvements in the speed of manufacturing, thereby lowering the cost.

Double seams make extensive use of rollers in shaping the can, lid and the final double seam. To make a sanitary can and lid suitable for double seaming, manufacture begins with a sheet of coated tin plate. To create the can body rectangles are cut and curled around a die and welded together creating a cylinder with a side seam.

Rollers are then used to flare out one or both ends of the cylinder to create a quarter circle flange around the circumference. Great care and precision are required to ensure that the welded sides are perfectly aligned, as any misalignment will mean that the shape of the flange is inconsistent, compromising its integrity.

A circle is then cut from the sheet using a die cutter. The circle is shaped in a stamping press to create a downward countersink to fit snugly in to the can body. The result can be compared to an upside down and very flat top hat. The outer edge is then curled down and around approximately 140 degrees using rollers creating the end curl.

The final result is a steel tube with a flanged edge, and a countersunk steel disc with a curled edge. A rubber compound is put inside the curl.

Seaming

The body and end are brought together in a seamer and held in place by the base plate and chuck, respectively. The base plate provides a sure footing for the can body during the seaming operation and the chuck fits snugly in to the end (lid). The result is the countersink of the end sits inside the top of the can body just below the flange. The end curl protrudes slightly beyond the flange.

First operation

Once brought together in the seamer, the seaming head presses a special first operation roller against the end curl. The end curl is pressed against the flange curling it in toward the body and under the flange. The flange is also bent downward and the end and body are now loosely joined together. The 1st operation roller is then retracted. At this point during manufacture five thicknesses of steel exist in the seam. From the outside in they are; a) End, b) Flange, c) End Curl, d) Body, e) Countersink. This is the first seam. All the parts of the seam are now aligned and ready for the final stage.

Second operation

The seaming head then engages the second operation roller against the partly formed seam. The second operation presses all five steel components together tightly to form the final seal. The five layers in the final seam are then called; a) End, b) Body Hook, c) Cover Hook, d) Body, e) Countersink. All sanitary cans require a filling medium within the seam as metal to metal contact, otherwise such an arrangement would not maintain its hermetic seal for very long. In most cases a rubberized sealing compound is placed inside the end curl radius, forming the actual critical contact point between the end and the body.

Probably the most important innovation since the introduction of double seams is the welded side seam. Prior to the welded side seam the can body was folded and/or soldered together, leaving a relatively thick side seam. The thick side seam meant that at the side seam end juncture the end curl had more metal to curl around before closing in behind the Body Hook or flange, leaving a greater opportunity for error.

Seamer setup and quality assurance

Many different parts during the seaming process are critical in ensuring that a can is airtight and vacuum sealed. The dangers of a can that is not hermetically sealed are contamination by foreign objects (bacteria as well as fungucide sprays) or that the can could leak its contents or become spoilt.

The most important part is the seamer setup. This process is usually performed by an experienced technician with many years of experience. Amongst the parts that need setup are seamer rolls and chucks which have to be set in their exact position (using a feeler gauge or a [clearance gauge] ). The lifter pressure and position, roll and chuck designs, tooling wear (as well as breakage in their respective bearings) all contribute to a good [double seam] .

Quality control usually involves taking full cans from the line - one per seamer head, at least once or twice per shift, and performing a teardown operation (wrinkle/tightness), mechanical tests (external thickness, seamer length/height and countersink) as well as cutting the seam open with a twin blade saw and measuring with a double seam inspection system. The combination of these measurements will determine if the seam is good or not.

It is important to note that incorrect setups can often be non-intuitive. For example, due to the [springback] effect, a seam can appear loose when in reality it was closed too tight and has just opened up like a spring. For this reason, experienced operators and good seamer setup tools are critical to ensure that the double seam is properly closed.

See also

* Food preservation
* Home canning
* Pasteurization

Incidents and accidents related to tinned foods

* Lead poisoning
* Botulism
* Bisphenol A

Famous canned foods

* Spam
* Vienna sausage
* Baked beans
* Pineapple
* Tomato Soup

References

* N.N. Potter, J.H. Hotchkiss. Food Science. 5th ed. Springer, 1999
* P.J. Fellows. Food Processing Technology: Principles and Practice, 2nd Edition . Woodhead Pub. 1999
* FDA 21CFR113.3 Thermally processed low acid foods packaged in hermetically sealed containers. Revision Apr.2006 [http://a257.g.akamaitech.net/7/257/2422/14mar20010800/edocket.access.gpo.gov/cfr_2002/aprqtr/21cfr113.3.htm]
* [http://www.qbyv.com/double_seamer_problems seaming problems and solutions]

External links

* [http://www.uga.edu/nchfp/how/can_home.html National Center for Home Food Preservation]
* [http://www.stavanger.museum.no/Eng/Hermetikk/hermhist.htm The history of the Norwegian Canning Industry]
* [http://foodquality.wfp.org/FoodSafetyandHygiene/FoodHandling/CannedFood/tabid/196/PageContentID/355/Default.aspx Handling Canned Food]
* [http://www.uga.edu/nchfp/publications/publications_usda.html USDA Complete Guide to Home Canning]
* [http://www.bsu.edu/library/article/0,,29253--,00.html Richard Roller Papers] , documents the history of glass manufacturing, with an emphasis on fruit and vegetable canning jars at the Ball State University Archives and Special Collections Research Center
* [http://www.hrs-spiratube.com/en/resources/aseptic_filling_fundamentals.aspx Aseptic filling fundamentals]
* [http://www.canseamers.com Bubber Machine Tools (manufacturer)]
* [http://www.qbyv.com/double_seamer_problems seaming problems and solutions]
* [http://www.qbyv.com/Clearance_Gauge Clearance gauge]
* [http://www.imetasrl.com/imeta/modules.php?name=Main&file=article&sid=15 feeler gauges]
* [http://www.qbyv.com/SEAMetal_HD double seam scope]
* [http://www.the-canopener.com The worlds only website solely dedicated to The Canopener]


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Canning — Saltar a navegación, búsqueda Canning puede referirse a: Canning, ciudad del Gran Buenos Aires, Argentina. Río Canning, río de Australia. George Canning, político británico. Apodaca Canning, tratado del siglo XIX, entre Inglaterra y España.… …   Wikipedia Español

  • Canning — Administration Pays  Canada Province …   Wikipédia en Français

  • CANNING (G.) — CANNING GEORGE (1770 1827) Grand homme d’État anglais, Canning est entré très tôt dans la vie politique en étant élu à l’âge de vingt quatre ans député de Newport. Juriste, fils d’un homme de loi, protégé d’un oncle banquier, il a commencé par… …   Encyclopédie Universelle

  • Canning — Canning. См. Консервация. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • Canning — (spr. Känning), 1) Georg, geb.[636] 11. April 1770 in London, wurde auf Kosten seiner Verwandten väterlicherseits, da seine Mutter nach des Vaters Tode als Schauspielerin nur ein spärliches Einkommen hatte, in der Rechtsschule (Lincolm Inn) zur… …   Pierer's Universal-Lexikon

  • Canning — Canning, 1) George, brit. Staatsmann, geb. 11. April 1770 in London, gest. 8. Aug. 1827, verwaiste früh und ward von seinem Oheim, einem Bankier in London, erzogen. Er studierte, ließ sich als Rechtsanwalt in London nieder und kam als Anhänger… …   Meyers Großes Konversations-Lexikon

  • Canning — (spr. känn ), George, brit. Staatsmann, geb. 11. April 1770 zu London, 1793 Mitglied des Unterhauses, 1796 Unterstaatssekretär, 1807 9 und wieder seit 1822 Minister des Auswärtigen, Febr. 1827 Premierminister, trat erfolgreich, obwohl Tory, für… …   Kleines Konversations-Lexikon

  • Canning [2] — Canning (spr. känn ), Sir Stratford, s. Stratford de Redcliffe …   Kleines Konversations-Lexikon

  • Canning — (Känning), George. geb. zu London d. 11. April 1770, studierte in Eaton und Oxford und kam 1793 durch einen verfaulten Flecken in das Parlament. Er hielt zu den Torys, wurde von Pitt bemerkt u. vorgezogen und kam nach dessen Tod in das… …   Herders Conversations-Lexikon

  • Canning — Canning, George …   Enciclopedia Universal

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”